Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
👷 What are the components of thermal power plant?Fundamental steam power plant components are Fuel handling plant, water treatment plant, ID fan , PA fan, Chimney, Water treatment plant, Steam Bo👷 What are the advantages of Thermal power plant?Steam power plants are economical (initially) as compared to power generation plants. Plants required less area to setup as compared to hydra power👷 What is the efficiency of steam power plant?Overall efficiency of power plants is low, which is 35-40%.👷 How does thermal power plant Work?Thermal power station’s working principle is “Heat released by burning fuel which produces (working fluid) (steam) from water. Generated steam runs👷 What is thermal generation?Power Generation by steam is possible by extreme power of Steam ( Which produced by water). To Convert water into steam, fuel required such as Heav👷 What are Top Thermal Power Plants in India?India is a country surprising the world with its incredible technology. When it comes to its trustworthy technology, the discussion would remain in Jan 30, 2018· Energy contributes to, and suffers from, water stress. Water-dependent thermal power plants generate the majority of the world’s electricity — more than 81 percent.These plants use fuels such as coal, gas or nuclear energy to make heat, which is then converted into electrical energy.
A thermal power station is a power station in which heat energy is converted to electric power.In most places the turbine is steam-driven.Water is heated, turns into steam and spins a steam turbine which drives an electrical generator.After it passes through the turbine the steam is condensed in a condenser and recycled to where it was heated. This is known as a Rankine cycle.
Mar 04, 2020· These mixed bed resins are used in Demineralization plant of boiler feed water treatment, to remove the ions (especially Na + and SO 3 2-) which may further present in the water after foregoing process of purification.. Degasser. The function of degasser tower is to remove carbonate ions by forming carbon-di-oxide. In degasser tower stream of water is poured from top and air is blown from
Mar 22, 2018· Thermal power plant or thermal power station is the place where we use the energy of heat to produce electric power, and it’s the most convenient sources of electric power generation, as we burn fuels such as oil, coal or liquefied natural gas to produce high temperature, high-pressure steam then we use this steam to turn a steam turbine
Sep 17, 2017· In a thermal power plant, to complete the cyclic operation, we need to send water again to the economizer at high pressure. Steam exhausted from LP turbine is not in condensed form and it is not economical to compress the steam at a very high pressure around 150 Kg/cm2.
Click to view57:46Dec 03, 2015· It's not possible to really understand cooling tower makeup water treatment, boiler feed water treatment or boiler water treatment without understanding basic water treatment chemistry and biology
Oct 05, 2010· Other key issues. Siting: The geographic location of power plants has a huge impact on cooling technology options, water availability, type of water used for cooling, and environmental impacts.Solar and geothermal power plants, for example, must be sited in areas with high solar radiation and geothermal energy, respectively—locations that may be arid and far from conventional water …
Author: David H. Paul, Inc. The Thermal power plant water steam cycle requires the steam to condense in a condenser. This requires an enormous quantity of water, known as Circulating Water. This affects the condenser vacuum which is the most important performance parameter in a power plant How much quantity of circulating water is required in a thermal power plant. This article briefly answers this.
Coal-based thermal power plants are the main source from which sulfur dioxide (SO 2) is released.Since the beginning of the 21st century, there has been a steady rise in the SO 2 emissions from nearly 118,000 Gg in 1970 to about 125,000 Gg in 2008 (Fig. 2.4).In fact, the emission level in USA has dropped down gradually since 1970, while that for China have increased.
J. Tominaga, in Advances in Steam Turbines for Modern Power Plants, 2017. 3.3.1 Cycle and features of BWRs. A BWR generates steam from demineralized water in the reactor itself, and uses the steam directly to drive the steam turbine. The configuration is simple compared to PWR which has steam generators, and the reactor pressure vessel (RPV) of BWR is designed in lower pressure conditions …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.