Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
A boiler that doesn’t have constant water pressure won’t be able to work as efficiently as it could do. Low pressure can often be an indication that there’s an issue with …
Superior Boiler offers both Low Pressure and High Pressure packaged steam boilers. These are ready-to-install systems featuring a perfectly matched powerful and efficient burner/boiler combination ideal for Space Heat and Industrial Process applications.
Low Pressure Boiler Engineer: Must have 3 months full-time experience (480 hours) in the operation of a boiler in this classification under an engineer who holds a valid low pressure or higher license or completion of a training course approved by the Department of Labor and Industry specific to low pressure boilers, a minimun of 40 hours
Boiler pressure is measured by a pressure gauge, usually situated inside a panel or underneath your boiler. We’ll discuss the ideal amount of boiler pressure in the next section. Whilst problems with the pressure of your boiler tend to be easy to diagnose and fix, …
The position set when the boiler was installed is sometimes shown by a red indicator needle. On most digital gauges, you’ll see a flashing pressure reading, if there’s a low (or high) pressure warning. If your boiler pressure reads less than 1 bar, it’s possible that you might have lost water from the system, which needs to be replaced.
User rating: 4.4/5 Low-pressure Boilers with an input of 100,000 BTUs or less *a mixed-use building has both commercial and residential units . Annual Inspection Cycle. January 1 to December 31. Inspections. Inspections can only be performed by authorized boiler inspectors licensed by the Department of Buildings or an authorized insurance company.
The standard cold water operating pressure of most U.S. and Canadian hot water boilers is 12 pounds per square inch (psi). If the boiler pressure drops below 12 psi, the valve will allow new water into the unit to bring up the pressure reading.
Low Pressure Boilers is the leading resource for preparing for low pressure boiler licensing or facility operating engineer licensing. This textbook provides a comprehensive overview of the latest information on the safe and efficient operation of low pressure steam and hot water boilers, cooling systems, and related equipment.
User rating: 5/5 Typical pressure for a residential boiler serving a two story home would show 12 psi cold, and less than 30 psi hot. Over 30 psi boiler pressure will cause the pressure relief valve to open. Typical operating temperature settings on a boiler call for a Low temperature (boiler cut-in) between 120 and 160 °F.
A boiler is an appliance designed to heat water and produce energy. The heat is applied to water in an enclosed container before being distributed throughout the system. The major difference between a low-pressure and a high-pressure boiler is the amount of pressure per square inch and pounds per square inch gauge that the boiler produces.
Boiler pressure too low can be a scary thing to deal with. After all, how does it actually work inside that big, white boiler? The designs of combi boiler systems are made to be economical, functional and reliable. But like any piece of equipment, it might need a checkup to ensure it runs efficiently.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.