Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
1. Possible to obtain good heat absorption, for the water tubes are zigzag arranged and the gas flows in a single pass at high speed. 2. Compact structure employing the heat transfer tube of finned tube type 3. Boiler water circulation pump is not required, as the boiler is of natural circulation type. 4.
Aug 21, 2017· Today on the Boiling Point, Jude Wolf will be talking about how the pre-heat feed water system works in a steam boiler. These systems are essential to …
Heat absorbed by water = 0.95 Vs(t 1 − t 2)MJ s −1,. t 1 and t 2 = temperature of hot gases before and after the W.H. boiler, °C.. Total heat as steam = sensible heat in feed water + heat absorbed by water in boiler. In good practice t 2, the temperature at which the flue gases leave the boiler, may be reduced to ca.50 K above the temperature of the water in the boiler.
Feed Water Heaters extract heat from boiler stack gases and then are returned directly to the water feeding the boiler, considerably reducing your fuel costs. Cannon’s Feedwater Heater line of products is an extremely flexible heat recovery line. This unit was designed in the 1980s to overcome the problems associated with heavy duty
This results in less fuel being used by the burner to generate steam. Waste heat from other sources such as diesel engines or gas turbines can also be used to pre-heat boiler feed water. 2. Waste heat boiler (WHB) or exhaust gas boiler (EGB) – a stand-alone unit is used to …
Boiler feedwater is an essential part of boiler operations. The feed water is put into the steam drum from a feed pump. In the steam drum the feed water is then turned into steam from the heat. After the steam is used it is then dumped to the main condenser.
Waste Heat Recovery Boilers (WHRB) - Wastetherm is manufactured by Thermodyne- are designed to recover heat from waste flue gases from DG exhaust, Furnace exhaust to produce steam or hot water. WHRB, industrial boilers are advanced enough to deliver max possible heat recovery & save money.
Heat recovery boilers are also often found in association with high temperature processes such as steel and glass making. It is not uncommon for these boilers to receive additional heat by supplementary firing of other by-products or by burning gas or light oil to raise the boiler inlet gas temperature to a level commensurate with the desired
2. Waste heat recovery systems. Waste heat recovery methods include capturing and transferring the waste heat from a process with a gas or liquid back to the system as an extra energy source .The energy source can be used to create additional heat or to generate electrical and mechanical power .. Waste heat can be rejected at any temperature; conventionally, the higher the temperature, the
May 27, 2020· A waste heat boiler of the water-tube design is able to cope with much higher pressures of steam than a fire-tube boiler, but it is more difficult to construct and install. Inside this type of boiler, there are narrower tubes than inside a fire-tube boiler, and the tubes contain water instead of hot gases.
Use Feedwater Economizers for Waste Heat Recovery A feedwater economizer reduces steam boiler fuel requirements by transferring heat from the flue gas to incoming feedwater. Boiler flue gases are often rejected to the stack at temperatures more than 100°F to 150°F higher than the temperature of the generated steam. Generally, boiler
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.