Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Heating · Contact Us · Weight · About Us The actual wall is always thicker than the specified minimum. The producing mills and R- S Matco, Inc. use the ASTM A-450 formula, but multiply the thickness by 1.10 for tubes with an OD less than 1-1/2” and 1.11 for 1-1/2” OD and larger and use that number for the wall thickness in the formula.
Apr 18, 2014· A low mass boiler will come up to temperature very quickly as it does not have a lot of water to heat. This is ideal in applications that handle heating and domestic hot water needs. So, if I have a 2,500 square foot house that has one zone of in-floor heat the boiler can go from 120 degrees for the heating of the floor to 180 degrees for
I don't think low mass boilers are cheaper. Maybe when compared to Buderus and Viessman but these are more then any other boiler. You do have cast iron low mass: Slantfin, Biasi, Crown Freeport (Low water , not low mass!). Burnham, Thermo-dynamics and Laars have steel models that are not cheap and usually have 15 yr min warranties if not lifetime.
The "out-of-balance" boiler hanger rods are adjusted once the load distribution of the support structure is known. The rods can be adjusted singularly, in pairs, or in complete rows, depending upon the design of the boiler. Boiler weighing tools are placed on all rods that are to be balanced simultaneously.
How much volume of steam will produce when one litre ofAug 12, 2018To produce one ton steam per hour, how much wood isJul 01, 2018How much fuel required for 1TPH boiler?Mar 09, 2018To produce 1 ton of steam per hour, how much water flow isApr 14, 2017See more results Disclaimer: Whilst every effort has been made in building this calculator, we are not to be held liable for any damages or monetary losses arising out of or in connection with the use of it. This tool is here purely as a service to you, please use it at your own risk. Full disclaimer.Do not use calculations for anything where loss of life, money, property, etc could result from inaccurate
10 - 20 MW 0 - 10 MW • 29 % manuf. residue • 28% landfill diverted • 21% ag residue About 15% of total biomass available and about 12% of forest-based A 10 MW (megawatt) generator can supply electricity to about 10,000 homes. biomass available The 7 cogeneration facilities are co-located with sawmills
The mass won't change, so 1 kg of liquid water will form 1 kg of steam. Taking the density of water to be 1 g/cm³, you need 1 L of water to produce 1 kg of steam (in actual fact, you need a bit more, since water is not quite that dense). To make 1
Dec 22, 2011· It ultimately comes down to economics, as do most things. The current trend is to market low-mass (light-weight) boilers against traditional heavy, high-mass cast-iron boilers. However, there are non-publicized risks involved that must be assessed and quantified. New gas-fired appliances in particular have a technological efficiency milepost that must be considered. Specifically, the
GMC-LT Serial vibratory road rollers effect powerful centrifugal force and great static linear load. They can be divided into 10ton road roller, 12 ton road roller, 14 ton road roller, 16ton road roller, 18ton road road, and 20 ton road rollers.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.