MENU
products
  1. Home
  2. --
  3. Industrial boilers

may i know how much the of a thermal plant of a capacity of 1000mw fuel by steam and coal boilers and natural gas

Product Thermal Capacity: 1 - 20 t/h

Working Pressure: 0.7 - 2 Mpa

Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.

Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.

Get a Quote Send Message

Introduction of WNS gas / oil fired steam boiler:

WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.

Technical advantages:

1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.

2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.

3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.

4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.

Thermal power station - Wikiped

The energy efficiency of a conventional thermal power station is defined as saleable energy produced as a percent of the heating value of the fuel consumed. A simple cycle gas turbine achieves energy conversion efficiencies from 20 to 35%. Typical coal-based power plants operating at steam pressures of 170 bar and 570 °C run at efficiency of 35 to 38 %, with state-of-the-art fossil fuel

STANDARD TECHNICAL SPECIFICATION FOR MAIN PLANT

utilities and equipment manufacturers, has completed its task of finalizing standard technical specification for Main Plant Package for a coal based thermal power project having 2x (500MW or above) sub-critical units. The specification covers scope, design criteria, equipment features, quality

Generation Cost Calculation for 660 MW Thermal Power Plan

Coal based Thermal Power Projects Norms for Operations FY 2009-14 1 Plant Availability Factor 85% 2 Gross Station Heat Rate For existing Stations 200/210/250 MW Sets 2500 500 MW and above 2425 3 Secondary Fuel Oil Consumption Coal Based 1.0 ml/Kwh 4 Auxiliary Energy Consumption 200 MW Series 9.0%/8.5% 500 MW Series(Steam driven BFP)

Basic Layout and Working of a Thermal Power Pla

Almost two third of electricity requirement of the world is fulfilled by thermal power plants (or thermal power stations).In these power stations, steam is produced by burning some fossil fuel (e.g. coal) and then used to run a steam turbine.Thus, a thermal power station may sometimes called as a Steam Power Station.After the steam passes through the steam turbine, it is condensed in a

A Solar Power Plant vs. A Natural Gas Power Plant: Capit

Apr 01, 2016· A 1000MW NG generation site (may have more than one generation plant) takes up a small fraction of the land area of a PV solar facility, assuming the solar facility would require to have between two and three times the plate capacity of the NG plant in …

COST ESTIMATES FOR THERMAL PEAKING PLANT “FINAL

expenditure (O&M) cost estimates for thermal peaking plant with nominal capacities of 40MW, 50MW, 100MW and 160MW. The scope of the study included cost estimates for both liquid and gas fired peaking plant. The cost of gas compressors for gas fuelled engines and the cost of liquid fuel systems

What is the cost to set up a 10MW thermal plant? - Quo

Jul 16, 2016· To find out the exact cost for a thermal power plant is quiet complex. In my opinion, the cost may be about 5 to 7 crores per MW. So, the estimated cost may be about 50 to 70 crores INR for a 10 MW thermal power unit. The major factors affecting t

Thermal Power Generation Plant or Thermal Power Stati

Mar 15, 2020· In coal thermal power plant, the steam is produced in high pressure in the steam boiler due to burning of fuel (pulverized coal) in boiler furnaces. This steam is further supper heated in a superheater. This superheated steam then enters into the turbine and rotates the turbine blades. The turbine is mechanically so coupled with alternator that its rotor will rotate with the rotation of

How to improve the thermal efficiency of a power plant - Quo

Because the isentropic efficiency of the largest gas and steam turbines is close to the theoretical limit only four factors can make significant changes. 1. Increase the average source temperature. 2. Reduce the average sink temperature. 3. Reduce

Thermal power plant - Simple English Wikipedia, the fr

A thermal power plant is a power plant where steam is used to drive a steam turbine.This turbine is connected to an electrical generator. After this, the water is condensed, and may be used again.This is known as the Rankine cycle.There are different procedures that can be used to heat the water;

Thermal Power Plant - Thermodyne Boile

Thermal Power Station process flowchart and diagram. The fuel is transported from mines via trains to the fuel storage facility in a power plant. The fuel transported to the plant is generally bigger in particle size and before it is fed to the boiler furnace it is broken down into smaller pieces using crushers.The fuel is then fed to the boiler generating a large amount of combustion heat.

Contact Us

zhulin@zozen.com

No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China

0086-510-68530066, +86-13506151292

Get Latest Price
Get in Touch

If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!

  • Boiler type
  • Name
  • email
  • Phone or Whatsapp
  • message
I accept the Data Protection Declaration

Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.

top