Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
A correctional institution in the US awarded Indeck a contract for the supply of a Heat Recovery Steam Generator (HRSG) system with auxiliary equipment to generate steam from waste gas. The Incline HRSG reclaims waste heat from a Centaur 40 gas turbine and supplies 19,200 PPH / 135 PSIG steam to the prison for heating and process users.
The mixture is typically concentrated in an evaporator and is then passed on to the recovery boiler for combustion. Whether black liquor, exhaust gas, or some other waste product is recycled, the waste product is burned in the combustion chamber of a recovery boiler. Heat produced by this combustion is typically used to heat water to create steam.
A waste heat recovery unit (WHRU) is an energy recovery heat exchanger that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. The WHRU is a tool involved in cogeneration.Waste heat may be extracted from sources such as hot flue gases from a diesel generator, steam from cooling towers, or even waste water from
approach is used to evaluate waste heat quantity, quality, recovery practices, and technology barriers in some of the largest energyconsuming units in U.S. manufacturing. The results from this investigation serve as a basis for understanding the state of waste heat recovery and providing recommendations for
The efficiency of generating power from waste heat recovery is heavily dependent on the temperature of the waste heat source. In general, economically feasible power generation from waste heat has been limited primarily to medium- to high-temperature waste heat sources (i.e., > 500 oF). Emerging technologies, such as organic
Typically, boilers combust waste for energy recovery, while industrial furnaces burn waste for both energy and material recovery. The original BIF regulations were primarily administrative, requiring notification and certain waste management practices.
Incorporates Worked-Out Real-World Problems. Steam Generators and Waste Heat Boilers: For Process and Plant Engineers focuses on the thermal design and performance aspects of steam generators, HRSGs and fire tube, water tube waste heat boilers including air heaters, and condensing economizers.Over 120 real-life problems are fully worked out which will help plant engineers in …
In Lees' Loss Prevention in the Process Industries (Fourth Edition), 2012. 12.8.4 Waste Heat Boilers. Process heat recovery boilers, or waste heat boilers, are widely used, particularly on ethylene and ammonia plants and on sulfuric acid and nitric acid plants.This type of boiler has developed as a cross between a conventional shell-and-tube heat exchanger and a firetube boiler.
SUPERIOR – Superior Boiler Works, Inc. offers waste heat recovery boilers in three basic designs to provide the greatest flexibility of any manufacturer in selecting a unit that is designed to meet the specific requirements of each application. Boiler designs are customized for specific job conditions to provide optimum performance and maximum energy savings.
Waste Heat Recovery Boilers (WHRB) - Wastetherm is manufactured by Thermodyne- are designed to recover heat from waste flue gases from DG exhaust, Furnace exhaust to produce steam or hot water. WHRB, industrial boilers are advanced enough to deliver max possible heat recovery & save money.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.