Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Figure 1. Each thermal fluid heating system should be designed specifically for your facility to meet your process needs. An inert gas blanketed expansion tank, which can be insulated if necessary, is recommended for systems that operate with a bulk temperature above 500°F (260°C).
A thermal fluid system is more than just a heater, and all the components of the system must work together in harmony for proper performance. Purchasing a complete thermal fluid system from Sigma Thermal will ensure that your system operation functions reliably.
For a thermal fluid to burn, it must remain hot enough to continuously generate vapor. Because liquid-phase thermal fluid systems operate under moderate pressure — typically a maximum of 100 psig at the circulation pump discharge — a leak will result in a fluid discharge into the surrounding area.
Liquid VS Vapor Thermal Fluid Heating. Thermal fluid heating can use liquid or vapor as the heat transfer medium. Liquid thermal fluid heating generally uses a closed loop system. The liquid remains as a fluid as it travels through the system. In vapor thermal fluid heating, the medium starts off as a fluid and is vaporized either within the
Apr 13, 2020· If you are looking to invest in a new thermal fluid heating system that requires minimal maintenance, be sure to keep American Heating Company in mind. Our industrial thermal fluid heaters are built using an innovative serpentine coil design that …
The heat in our range of electric thermal fluid heaters is provided by electrical boilers and therefore guarantees a 100% yield for the energy consumed. We use very low density electrical heaters (to minimize thermal fluid breakdown) and solid state relays for modulating power regulation.
Thermal Fluid Solutions provides a complete range of thermal fluid system support and maintenance services, as well as fluids and consumables. Our range of services include: Fluid Testing & Analysis, Flashpoint Recovery, Solids Removal, Drains & Refills, Compliance And Training, Water Removal. Partner With TFS Today
Aug 11, 2014· Fire safety is an ever-present concern for operators of thermal oil heating systems.To understand the scope of the problem, let’s review the salient facts. First and foremost, this is a relatively rare and well-understood threat to users of thermal oil heating systems.
Thermal Fluid vs. Steam A thermal fluid (hot oil) system operates in a closed loop circulation system with minimal pressure. Fulton thermal fluid systems can reach 750°F (345°C) making them an ideal choice for many process heat applications. The choice between a steam system or a thermal fluid system is governed by the process requirements.
Thermal Fluid Heaters Fulton is synonymous with heat transfer solutions and produces an unrivalled range of multi-fuel-fired steam and hot water boiler solutions. But, with a range of thermal oil systems the company should also be considered a major provider of thermal fluid solutions.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.