Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Author: Grim Fernando Note: Manufacturers of hot-oil heaters in these lists are not ranked in any order of preference, capability, or merit. They are all thermal fluid heater manufacturers that Paratherm Engineers have worked with and found to produce capable and excellent machinery.
Consult a solar heating professional or the local authority having jurisdiction to determine the requirements for heat transfer fluid in solar water heating systems in your area. Air Air will not freeze or boil, and is non-corrosive. However, it has a very low heat capacity, and tends to leak out of collectors, ducts, and dampers.
Thermal fluid heating systems use indirect methods for heating a substance or system. The heater is used to heat an intermediate liquid (often water, thermal oil or glycol). This intermediate liquid is then used to transfer heat to the end target. The end target can be process equipment, or other liquids during transfer or while […]
Thermal oil heaters require low maintenance. Fuel savings up to 20% compared to steam heating systems. A thermal fluid system consists of a closed circuit with minimum energy leaks. At least 90% of the fuel is used in the heating process.
The AHF series maximum flow air heaters are used with blowers or recirculating air in baking, drying, and preheating applications. This air heater is designed with a 23/8' O.D. aluminum tube and a cross frame heating element for minimum resistance to air flow.
The Complete Guide · Thermal Oil Heaters Heat Exchange and Transfer, Inc. designs and manufactures electrical thermal fluid heaters that are compact and skid mounted with operating temperatures up to 550⁰F using mineral oils and synthetic based heat transfer fluids.Our industrial hot oil heaters are used for a variety of applications including dryers and reactors. Call us today!
Author: Manufacturing Today Choosing An Electric Thermal Fluid Heater. Wattco electric thermal fluid heaters are custom engineered for your specific process. Materials, designs, flanges, and wattages are all customized to the medium, volume, and any other requirement. At Wattco, you can purchase the entire thermal fluid heater system from a single manufacturer. This makes
Figure 1. Each thermal fluid heating system should be designed specifically for your facility to meet your process needs. An inert gas blanketed expansion tank, which can be insulated if necessary, is recommended for systems that operate with a bulk temperature above 500°F (260°C).
Thermal design of a feedwater heater requires an economic optimization of many factors, including material and operating costs. Two publications which describe feedwater heaters, and their design, in some detail are those of BEAMA (1968) and HEI (1984).
Efficiency. Efficient industrial heating is important for a variety of reasons – both within your facility … The finned coils are heated by thermal fluid that flows inside the finned coils. The thermal fluid must be provided by an external source such as a thermal fluid heater (not included). For optimal performance, the heater should be installed in an independent hot oil circuit with its own hot oil pump.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.