Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Steam Boiler Pressure settings: This article describes the normal operating pressure range for residential steam heating systems and for commercial or high-rise building steam heating systems. The article also provides links to details about the pressure control and safety controls on steam heating systems & boilers. Questions & answers about residential steam heating system controls, valves
Steam System Design and Best Practices Related to Kiln Drying. Steam Boiler – high or low pressure Typical Steam Main Drip Station. New England Kiln Drying Association – Steam Design & Best Practices – HerLine Technologies Steam Traps in a Typical Steam Circuit.
The steam boiler is an old convection heating technology dating back over 200 years and is most commonly found in old homes. Because steam boilers operate at a higher temperature than hot-water boilers, they are inherently less efficient than their hot-water cousins and are more finicky to operate.
Steam boilers operate at a higher temperature than hot water boilers, and are inherently less efficient, but high-efficiency versions of all types of furnaces and boilers are currently available. To learn more about furnaces, boilers and other types of home heating systems, explore …
This section, General Engineering Data, covers four main areas. The first includes information on sizing of steam, water, natural gas, and fuel oil piping. It also provides information on stacks. Thermodynamic Properties contains information on fuel oils, water, and steam, including viscosities, thermal
Chapter 2 Boiler 101: typical NYC residential heating system One and two family homes often use forced-hot-air heating systems, which include a burner, heat exchanger and blower(s). In these types of systems, hot air is forced through ducts to every room in the house, where it blows out of vents that are usually located at floor level.
The HP boiler worked at approx 850 psi (5.86 MPa), and the low-pressure boiler at 200 to 250 psi (1.38 to 1.72 MPa). The UHP and HP boilers were of a water tube design, while the LP boiler was a fire tube boiler typical for steam locomotives. The LP cylinders were driven with a mixture of the HP cylinder exhaust and the LP boiler output.
Author: Bob Formisano Low pressure steam is considered to be up to 15 psi; high is generally 100 psi and higher. Superheat is a term that refers to higher temperature steam, as a result of a second special steam heat exchanger in the boiler that allows steam pressure to increase, thereby taking on more BTUs (in excess of 500 psi is typical of superheat).
File Size: 897KB Dec 11, 2017· Steam Boiler Diagram With Parts for Dummy’s. By MS Chaudhry | December 11, 2017. 1 Comment. Below is a typical steam boiler diagram for dummy’s to understand with name of each component or boiler part. First of all you should understand …
Infrequent or Irregular Maintenance. Irregular maintenance often is the heart of problems with … A typical steam distribution system consists of 1) Boiler where steam is generated . 2) Steam using equipment such as turbine , evaporator, reaction vessel, ejector, etc.
Oct 18, 2016· Achieving steam boiler efficiency can result in dramatic energy savings. According to the U.S. Department of Energy (DOE), a typical industrial facility that conducts a steam system assessment will identify potential steam system energy use and cost savings that …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.