Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Jan 08, 2018· High Modulation Rate: - Can work at 20-100% capacity without problems Low Steam Cost: - Low fuel cost with the cheap powder lignite - Low electricity consumption - Short start-up time - …
Author: Enhui Sun, Han Hu, Hangning Li, Jinliang Xu, Guohua Liu Drawing upon our extensive technical expertise and operating experience, B&W developed the Internal Recirculation Circulating Fluidized-Bed (IR-CFB) boiler which is the technology of choice for power plant owners seeking economy, reliability and flexibility. In addition, load-following capabilities are attainable with B&W’s in-bed heat exchanger technology.
Fluidized-bed gasifiers may differ in ash conditions (dry or agglomerated/slagging) and in design configurations for improving char use. Also, depending on the degree of fluidization and bed height, these types of reactors sometimes are also named as circulating fluidized bed …
The successful design and operation of a fluidized bed combustor requires the ability to control and mitigate ash-related problems. The main ash-related problem of biomass firing boiler is agglomeration. The fluidized bed boiler with steam capacity of 66 t/h (4 MPa, 440 °C) was started up at the Arkhangelsk Paper- Pulp- Plant in 2001.
Reviews: 2 4.8 Design of the Heated Fluidized Bed Reactor System 69 4.9 Biomass Feeder Design 69 4.10 Sand Feeder 71 4.11 Feeder Probe Design 71 4.12 Fluidized Bed Cover Plate 75 4.13 Heated Windbox Design 76 4.14 Flexible High Temperature Hose 78 4.15 Gas Meter 78 4.16 Thermocouples 78 4.17 Pumps, Piping and Gas Supply 81 4.18 Cold Gas Filter 81
EcoFluid Bubbling Fluidized Bed (BFB) boilers are used for steam and power generation from biomass and alternate fuels such as sludge, RDF, and residues. ANDRITZ fluidized bed technologies demonstrate unmatched fuel flexibility – even fuels which are difficult to …
In this paper, S-CO 2 cycle driven by pressurized fluidized bed combustion (PFBC) boiler is investigated, realizing compacter system design compared with that driven by atmospheric pressure combustion boiler. The research and development of PFBC boiler has lasted more than half century. The concept was initially proposed in 1967.
The effect of bed pressure drop and bed inventory on the performances of a circulating fluidized bed (CFB) boiler was studied. By using the state specification design theory, the fluidization state of the gas−solids flow in the furnace of conventional CFB boilers was reconstructed to operate at a much lower bed pressure drop by reducing bed inventory and control bed quality. Through
The present paper discusses the goals and methods of design of a circulating fluidized bed (CFB) boiler: A 62-MWt (75-T/h) CFB boiler was designed manually using experience and available published data. The design was regenerated by an Expert System for evaluation and confirmation of the manual design.
The Westinghouse R&D Center in Pittsburgh. Pennsylvania has also investigated circulating bed boiler concepts.^9 A deep recirculating fluidized-bed combustion boiler (Figure 20) was conceived by Westinghouse as an alternative to conventional atmospheric and pressurized fluid bed units.
Performance Evaluation and Optimization of Fluidized Bed Boiler in Ethanol Plant Using Irreversibility Analysis Article (PDF Available) in Case Studies in Thermal Engineering 10(C) · August 2017
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292
Get Latest PriceCopyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.
