Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Author: myfordboy Steam engine, machine using steam power to perform mechanical work through the agency of heat. In a steam engine, hot steam, usually supplied by a boiler, expands under pressure, and part of the heat energy is converted into work. Learn more about steam engines in this article.
What is the shrinking and swelling effect in boilersFeb 14, 2019What are the advantages of using a superheated steam in aMay 07, 2018What is the highest temperature that steam can attain in aApr 08, 2018What is the temperature of a boiler in a power plant?Jan 14, 2017See more results The firebox peak temperature is approximately 2,500 degrees F (~1371 ℃) In a steam engine, the firebox is the area where the fuel is burned, producing heat to boil the water in the boiler. Most are somewhat box-shaped, hence the name. The hot gases generated in the firebox are pulled through a rack of tubes running through the boiler
The boiler is used to convert water into steam.When fueled it converts feed water into steam at 165°C, matching the maximum temperature of the steam engine.Boilers have 2 water connectors, allowing them to pass water through to other adjacent equipment, but only 1 steam connector for output.
MERNACK also make complete units of the locomobile type (steam engine mounted on top of the boiler) with power output of 35 and 160 kW. The engine speed is about 240 rpm. The steam pressure is maximized at 10 and 14 bar respectively and the maximum steam temperature is 350°C.
Dimensions: 2×3 The steam may be further heated by passing it through a superheater on its way from the boiler to the engine. A common superheater is a group of parallel pipes with the surfaces exposed to the hot gases in the boiler furnace. Using superheaters, the steam may be heated beyond the temperature at which it is produced by simply boiling water under
To generate steam, you have to reach at least 100C, or 212 degrees Fahrenheit. However, the more pressure that exists in the boiler, the higher the temperature can be. So you could have a boiler with a water temp of 450 degrees F. Someone who know
10. Gas for Model Steam BoilersThere are three types of gas commonly used in firing model steam boilers. All may be labelled as LPG (Liquid Petroleum Gas) but for reasons set out below it is important to use their correct names.They are Propane, Butane and Isobutane. In Australia Propane is commonly labelled as LPG whe
Because a steam boiler makes heat by producing steam - by boiling water, at sea level, the temperature at the boiler will be boiling or 212 °F or close to that figure. The actual steam boiler temperature may be a bit lower at high elevations above sea level, and the steam …
Click to view17:04Nov 14, 2015· This little boiler was made to power the Myfordboy steam engine. It is kept simple and works well.
Steam engines are the most basic electricity generator, available to the player at the start of the game. They produce electricity by consuming steam, using water pumped from an offshore pump that was heated to 165°C steam with boilers or to 500°C steam with heat exchangers. Steam that has a higher temperature than the maximum temperature of the steam engine (165°C) is consumed at the
Nov 01, 2009· The parabolic trough provides solar steam production to power small steam engines. This engine can run for hours. I moved the pipe partially out of …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.