Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
CFBC boiler stands for circulating fluidized bed combustion boiler, the furnace is pressurised and the furnace gas is recirculated to capture the unburnt carbon, to increase the thermal efficiency of the boiler. Hence this is an improved version of AFBC. The CFBC boiler has …
Jun 26, 2007· A COMPARISON OF PC, CFB AND IGCC TECHNOLOGIES FOR BASIN ELECTRIC POWER COOPERATIVE'S DRY FORK STATION the combustion process by adding limestone to the fluidized bed. This is because the reaction of sulfur dioxide (S02) with limestone (calcium carbonate) peaks at about 1,500 of, which is in the range of CFB boiler combustion.
Circulating Fluidized Bed (CFB) Boiler Tube Erosion HVTS Claddings for CFB Boiler Tubes. IGS leverages decades of experience with over 500 Circulating Fluidized Bed (CFB) Boiler High Velocity Thermal Sprayed (HVTS) cladding applications to stay at the forefront of maximizing run time and minimizing outage frequency and cost for Coal Burning CFB Boilers globally.
If steam contains 10% water by mass, it's said to be 90% dry, or have a dryness fraction of 0.9. Steam dryness is important because it has a direct effect on the total amount of transferable energy contained within the steam (usually just latent heat), which affects heating efficiency and quality.
The time required to heat 75 kg of water (c p = 4.2 kJ/kg o C) from temperature 20 o C to 75 o C with steam produced from a boiler with capacity 200 kW (kJ/s) can be calculated by transforming eq. 2 to. t = m c p dT / q = (75 kg) (4.2 kJ/kg o C) ((75 o C) - (20 o C)) / (200 kJ/s) = 86 s. Note! - when steam is injected directly to the water all
Ultra-Supercritical Circulating Fluidized Bed (CFB) Boilers. 660 MWe for lignite B, higher for hard coal, for low-grade and difficult-to-burn fuels such as anthracite, lignite, petroleum coke, oil shale, discarded coal and biomass, GE offer circulating fluidized bed technologies with different arrangements suited to fuel .
The purpose of a paper machine steam and condensate system is to control steam pressures for optimum drying, provide stable control over the entire operating range and efficiently remove condensate from inside the dryers. This article presents tips for maintaining performance with your S&C systems.
Can someone help, I have a steam boiler, and have the KG Per hour steam rating the boiler can acheive (15,000kg/hr) , and need to convert that to the water capacity the boiler will hold thanks As cold water, 15000 kg is about 15000 L.
How much steam is required to heat water?Apr 28, 2017How much water is required to produce 1 kg of steam? See more results The weight of steam required to heat a given quantity of water from a certain temperature to boiling point can be found by the following rule:. Rule. Multiply the number of pounds of water to be heated by the number of degrees temperature the water is to be raised, and divide the product by the total heat of steam at the pressure it is to be used, less the sensible heat at atmospheric pressure.
A boiler operating at 100 psi has a dry saturated steam temperature of 338 F what is the boilers water temperature. more than one safety valve is required on boiler that have over. Filling the pump with fluid to establish suction and is also water leaving the boiler …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.