MENU
products
  1. Home
  2. --
  3. Industrial boilers

standard thickness of shell for 10 bar steam boiler

Product Thermal Capacity: 1 - 20 t/h

Working Pressure: 0.7 - 2 Mpa

Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.

Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.

Get a Quote Send Message

Introduction of WNS gas / oil fired steam boiler:

WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.

Technical advantages:

1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.

2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.

3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.

4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.

When did American Standard Stop making boilers — Heati

American Radiator and Sanitary Standard coal converted to gas boiler from the 1920's. That company joined to for American Standard. Until last year it was the sole unit that heated my home. Now it's a mere passageway for the hot water generated in an outdoor boiler. Pretty impressive longevity I think, however.

The Feedtank and Feedwater Conditioning | Spirax Sar

The return of condensate represents huge potential for energy savings in the boiler house. Condensate has a high heat content and approximately 1% less fuel is required for every 6°C temperature rise in the feedtank. Figure 3.11.5(a) shows the formation of steam at 10 bar g when the boiler is supplied with cold feedwater at 10°C.

Boiler Material - IB

10" pipe is 10 3/4" OD. In a boiler this size (10-inch diameter by 41-inch length) I usually use 5/16" plate. I use only PVQ plate. Sa285 GrC is getting harder to find these days. SA516 Gr70 is much easier to get. Boiler plate used be sold as firebox quality or flange quality.

Boiler – Fundamentals and Best Practic

Steam Production From steam tables we can see that the total heat of steam does not vary a great deal as the boiler pressure increase The boiling point (b.p.) increases as the pressure increases Thus the sensible heat increases as the pressure increases, and the latent heat decreases Boiler pressures are expressed in psia, psig, bar, kg/cm2

Standard Steam Boile

Beckmann, Limited Model VFT-30 wood fired steam boiler drives a Strath Model Warrego 3" X 4" single cylinder double acting engine with Stephenson gear. At Left: A standard HWT-S25 wood fired boiler with Tiny Power 3"X4" M.

PROCESS DESIGN OF STEAM BOILERS (PROJECT STANDARDS

PROCESS DESIGN OF STEAM BOILERS (PROJECT STANDARDS AND SPECIFICATIONS) Page 3 of 45 Rev: 01 April 2011 SCOPE This Project Standards and Specifications is intended to cover minimum requirements for process design of field erected water tube boilers. REFERENCES Throughout this Standard the following dated and undated standards/codes are referred to.

(PDF) Selection and Analysis of Material for Boiler Pip

Selection and Analysis of Material for Boiler Pipes in a Steam Plant.pdf The supporting structure of the boiler was built of the standard steel profiles and thin (38 bar), steam

DRAFT BOILER/FEEDWATER GUIDELIN

3.4.3.1 Hard scale is formed in firetube steam boilers on tubes and the shell in contact with boiler water and at the steam and water interface. In watertube boilers, hard scale forms at the steam and water interface of the steam drum shell or flash chambers and on the inside of …

IOP Conference Series: Materials Science and Engineeri

(combo boiler) in which flue gas and water flow both outside and inside the tubes; the type contains an external furnace and shell-type boiler in a sequence. Fire tube boilers of smaller size are vertical and those of larger size are horizontal. The minimum capacity of a water tube boiler is usually around 5 tph.

Boiler Water Treatment Part 2 – Internal Treatme

To keep a steam boiler producing 4000 kg/hr of steam below 3500 ppm TDS when fed from a feed tank having a TDS of 80ppm, it will need to blowdown at least; F 80 ppm 80 × 4000 = 93.6 kg/hr S 4000 kg/hr 3500 − 80 B 3500 ppm Typical permissible levels of boiler water TDS . Type of Boiler TDS level in parts per million (ppm)

standard thickness of shell for 10 bar steam boil

The boiler shall be rated 2000kg/hr steam boiler | Industrial Boiler 2000kg/hr steam boiler. Taijune offers wide range of energy-efficient oil-fired steam boiler and gas boiler to make steam Exclusive for 200kg/hr~2000kg/hr standard thickness of shell for 10 bar steam boiler standard thickness of shell for 10 bar steam . Get a Quote

Contact Us

zhulin@zozen.com

No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China

0086-510-68530066, +86-13506151292

Get Latest Price
Get in Touch

If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!

  • Boiler type
  • Name
  • email
  • Phone or Whatsapp
  • message
I accept the Data Protection Declaration

Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.

top